0512-66717681

Knowledge about PC acrylic anti-static panels

2020.11.23

Polycarbonate material, also known as PC (hereinafter referred to as PC), has excellent optical and physical mechanical properties, and is therefore widely used in the manufacture of aircraft transparent parts, vehicle windows, face masks and other products. However, this material also has some shortcomings, and the diversification of products has raised more and higher requirements for the performance of PC materials. However, the wear resistance, ultraviolet radiation resistance and alkali resistance of PC materials are poor, especially the poor wear resistance, which greatly limits the application scenarios of PC materials. Currently, an effective method is to apply a wear-resistant coating on the surface of the sheet.

In the early stage of the development of PC wear-resistant coatings, many companies directly added inorganic nanoparticles to the coating resin. The most typical representative achievements were two types: one was to add modified nano-ceramic powder to the resin to enhance the wear resistance of the cured coating, mainly used for the wear protection of transparent masks. The other was to directly add nano-alumina to the transparent resin to significantly increase the hardness of the resulting coating, enhancing the wear resistance and scratch resistance of the coating. The wear resistance of this coating was approximately 2 to 8 times that of the coating without adding nano-alumina, and it also had good anti-corrosion function, which could be used for the surface protection of various transparent plastics and high-gloss metal sheets.

However, this coating has far exceeded the protective requirements as the application field of PC expands. Therefore, later, with the changes in demand, PC transparent part wear-resistant coatings gradually formed poly siloxane type wear-resistant coatings, acrylic ultraviolet light curing wear-resistant coatings, polyurethane wear-resistant coatings and inorganic coatings. Among them, the poly siloxane type wear-resistant coatings are the most widely used.

Poly siloxane coatings mainly include two types: the first type is a coating prepared by directly using siloxane monomers through hydrolysis and condensation, adding an adhesion promoter to obtain a transparent wear-resistant coating; the second type is a coating prepared by modifying siliceous sol with siloxane monomers, further condensing, and adding an adhesion promoter to obtain a transparent wear-resistant coating.

There are many types of wear-resistant coatings, including poly siloxane coatings, acrylic ultraviolet light curing coatings, and polyurethane coatings. The application methods and curing processes are also diverse, including brushing, spraying, immersion coating and spin coating; inorganic coatings mainly include sputtering method, physical vapor deposition and chemical vapor deposition methods. The curing processes are basically divided into room temperature curing, heat curing and ultraviolet light curing.

Next, let's introduce the coating process in detail.

1. Brushing
Also known as flow coating or pouring coating, this method is a coating method in which the coating is sprayed or flows over the surface of the workpiece. During the brushing process, as the construction progresses, the solvent of the coating volatilizes, changing the construction viscosity of the coating. Therefore, the selection of the solvent evaporation rate of the coating system is crucial for the brushing process.

2. Spraying
Spraying mainly uses a spray gun, using pressure to cause the coating to atomize and disperse into uniform and fine droplets, coating the surface of the coated workpiece. There are many types of spraying methods, and the currently widely used main spraying methods include electrostatic spraying, airless spraying and air spraying, etc. The coating prepared by spraying is uniform, but during the spraying process, the highly atomized coating is prone to cause pollution to the environment and is not conducive to human health. This method has low utilization rate and large economic losses.

3. Immersion coating
This method is to immerse the workpiece to be coated completely in the container containing the coating, and after a certain period of time (usually very short), take it out of the tank and let the excess coating flow back into the container. This coating method has the advantages of high production efficiency, less coating loss and simple operation. However, it is not suitable for large workpieces.

4. Spin coating
This method is currently mainly used in the electronics industry. The approach is to make the substrate being coated rotate vertically with respect to its own surface, while applying the coating onto the substrate. Through rotation, the coating is evenly applied to the coated substrate.

5 Rolling Coating
After the processing by rolling coating, the sheet is called a rolling-coated board. The rolling-coated board is formed by applying the coating to the surface of the substrate after it has undergone degreasing and chemical treatment, and then drying and curing. Through high-performance rolling coating processing technology, the accuracy and flatness of the sheet can be more effectively controlled, and the traditional causes of unevenness and wrinkles can be successfully eliminated. Depending on the different coatings and rolling coating methods, there are certain differences in the quality of the rolling-coated board.

Zhongweike: By integrating several coating processes and considering the large area, diverse structure, and high usage environment requirements of PC sheets, most of them adopt the spray coating process. The main reason is that the spray coating process is significantly superior to other coating processes in terms of coating adhesion, durability, and coating effect. Overall, the development of polycarbonate transparent wear-resistant coating to this day has been relatively mature, with its own advantages. In addition to ensuring wear resistance and scratch resistance, the coating wear-resistant material is developing towards the direction of including composite functional requirements such as anti-ultraviolet, anti-static, and anti-aging. We believe that with the continuous development of polycarbonate technology, the application scenarios of wear-resistant coatings will also become broader.

The Zhongweike anti-static board is completed in a thousand-level cleanroom. Nine high-performance plastic surface functional coatings: anti-static, high hardness, ultra-mobility, outdoor weather resistance (anti-UV), anti-blue light, anti-glare, anti-fingerprint, anti-fogging, and anti-infrared. Among them, the anti-static board and anti-fog board have been tested in the market. At the same time, the company focuses on the research and development of new products and possesses a number of high-performance sheet surface treatment technologies.


Previous:Related to goggles lenses and PC protective plates

Next:Upgrade of raw material particles for Zhongweike polycarbonate PC sheet and film products